Backlit Panels




Quantity: 1; Dimensions in CM: 100x100; Panel Type: 3 mm opal Plexiglass; Print type: Direct UV printing; Cut: Straight Cut; Drilling: Without Holes; Packaging: Two 40 MM polystyrene sheets with perimeter bumper
Backlit panels in opal Plexiglas are printed sheets to mount on an illuminated support: signs, restaurant and bar menus, displays and in-store communication. The sheet is opal Plexiglas in 3 or 5 mm, and the graphics are made by direct UV print or with clear glossy adhesive PVC applied to the surface. The configurator covers the printed panel only: the structure and the lighting system are not part of the options. You can choose glossy or matt lamination with UV filter, square or contour cutting and drilling. Free sizes, from 1 to 250 pieces.
Take a look at these too
Custom opal Plexiglas backlit panel
A backlit panel is a printed sheet that is lit from behind. It is used for signs, illuminated menus in restaurants and bars, displays and in-store messages that need to stay readable even in low light. Here you order the opal sheet with your artwork, ready to fit into the lightbox or illuminated structure you already have.
Material and print options
- Panel Type: opal Plexiglas, 3 mm or 5 mm.
- Print type: direct UV print on the sheet, or application of printed adhesive PVC.
- Material: for the application option, clear glossy adhesive PVC is used, which lets the light from the sheet pass through.
- Material Quality: Standard or Long Life.
- Lamination: none, glossy with UV filter, or matt with UV filter.
- Lamination Quality: Standard or Extra UV Guard.
- Cutting: square cut for rectangular lightboxes, contour cut for special shapes.
- Drilling: no holes, four holes at the corners, or two holes in the center of the left and right sides.
- Packaging: no packaging with pickup at our site, or two 40 mm polystyrene boards with perimeter edge protectors.
Thickness and backlighting: how to choose
Both opal sheets diffuse light evenly, which is what backlighting needs. The 3 mm sheet is light and flexible, suited to small signs or wherever weight needs to be kept down. For a large panel we recommend the 5 mm sheet: its greater rigidity prevents flexing that could make it slip out of the guides of the structure. Contour cutting follows the vector path in your file and lets you create curved profiles. Among the films, Standard is suited to indoor use and temporary outdoor use, while Long Life is polymeric, with high dimensional stability.
Sizes and quantities
Sizes are free. Measure the housing of your illuminated structure and enter width and height in centimeters. You can order a single panel or multiple pieces, up to 250: useful if you need to replace the graphics in several stores. The price is calculated by the configurator based on size, quantity and options.
How to order and prepare your file
Choose the thickness and print type, set the cutting and holes, then upload your artwork. Before sending the file, read the file preparation instructions. The configurator shows the available production times; delivery also depends on the chosen shipping method.
Where backlit panels are used
Each use calls for a different configuration. These are the most common cases.
- Rectangular sign in a lightbox with guides: square cut, no holes, with the same thickness the housing accepts. For a large sign choose the 5 mm.
- Sign with a special profile: contour cut, which follows the vector path in your file and allows free shapes and curved profiles.
- Illuminated panel fixed to a wall: four 5 mm holes at the corners, for fixing with screws or spacers.
- Panel hung horizontally: two 5 mm holes in the center of the right and left sides.
- Menu or price list that needs updating over time: adhesive PVC application, because the graphics can be replaced while keeping the sheet, when its condition allows.
- Point-of-sale display: square or contour cut depending on the shape, with matt lamination if spotlights or other direct lights hit the panel.
- Same graphics in several stores: a single order with the quantity you need, up to 250 pieces.
Direct UV print or clear adhesive: how to decide
With direct UV print the graphics are printed on the opal sheet. The panel comes as a single piece, with no films to apply.
With adhesive PVC application the graphics are printed on a clear glossy film with permanent adhesive, then applied to the sheet. The film is clear, so light passes through the graphics and the background stays opal. With lamination the graphics also get protection against scratches. The main advantage is the possibility of replacing the graphics while keeping the sheet, if it is still in good condition: useful for menus, price lists and promotions that change.
Lamination for backlit panels
- None: the print has no additional protection. Recommended only for temporary indoor use.
- Glossy with UV filter: a glossy protective film that protects the print from scratches, sunlight and weather.
- Matt with UV filter: a matt film with an anti-glare satin effect, protecting against scratches and sunlight. It is useful when direct lights hit the panel and would create reflections.
The Standard Lamination Quality is monomeric. Extra UV Guard is a polymeric lamination with reinforced UV protection, designed for long-term outdoor applications. A practical guide to combinations:
- indoor menu or display: Standard film and Standard lamination;
- outdoor sign that stays mounted for a long time: Long Life film with Extra UV Guard lamination;
- short-term indoor setup: even without lamination.
Measuring the structure before ordering
Sizes are free, so you take the right measurements from the structure you already have. Before configuring:
- measure the width and height of the housing the sheet fits into;
- check which thickness the guides accept, 3 mm or 5 mm;
- if you are replacing an existing sheet, also note the position of any holes;
- enter width and height in centimeters in the configurator.
If the structure has a frame that covers the edges, allow for the part that will stay hidden. If more than one sheet needs replacing, measure each housing separately: even similar structures can have different housings, and different sizes require separate configurations.
How to prepare your file for backlit panels
- Set up the document with the same proportions as the sheet.
- Keep text and logos in the visible area, outside the area covered by the frame or guides.
- Trimming can remove 1-2 mm: keep important elements at least 2-3 mm inside the finished size.
- With contour cutting the file must include a dedicated cut path. If the graphics extend to the path, an outer bleed is needed: the measurement is given in the file instructions.
- If you request holes, keep the area around the drilling points clear.
- For resolution and format, see the file instructions.
Packaging, shipping and pickup
For shipping, choose the packaging with two 40 mm polystyrene boards and perimeter edge protectors, a protective package designed for transport. The no packaging option applies only to direct pickup at the production site.
Backlit panels: mistakes to avoid
- Ordering a thickness different from the one accepted by the guides of the structure.
- Choosing 3 mm for a large sign: the thinner sheet flexes more and can slip out of the guides.
- Leaving a panel that stays exposed outdoors without lamination.
- Requesting contour cutting without a cut path in the file.
- Assuming that the lightbox or lights are included: the options cover the sheet only.
- Using this page for a sign that will not be illuminated: for those cases see Forex panel printing or Dibond and aluminum printing.
Frequently asked questions about backlit panels
Are the lightbox and lights included?
No. The options cover only the printed opal Plexiglas sheet, to be mounted on an existing illuminated structure, LED or otherwise.
What thickness should I choose for the panel?
3 mm and 5 mm are available. Check which thickness the housing of your structure accepts.
Can I have a non-rectangular shape?
Yes, with contour cutting.
How are the graphics made?
By direct UV print on the sheet, or on clear glossy adhesive PVC that is then applied.
Can I order a custom panel for a wall project?
Yes. Sizes are free and drilling allows fixing with four holes at the corners. Whoever handles the installation of the lighting system must plan for it separately.
Can I change the graphics and keep the same sheet?
With adhesive PVC application the graphics can be replaced while keeping the sheet, when its condition allows. With direct UV print the graphics are printed on the sheet.
Which lamination should I choose for an outdoor sign?
A lamination with UV filter, glossy or matt. For a long-term outdoor application, combine the Long Life film with the Extra UV Guard quality.
What diameter are the holes?
5 mm, both in the drilling with four holes at the corners and in the one with two holes in the center of the sides.
Related products
For non-illuminated panels see Forex printing and Dibond and aluminum printing; for cut-out letters and logos there is the Plexiglas lettering. The whole range is in Panel printing.
When to choose another page. If you need a printed Plexiglas sheet for another use, see the Plexiglas printing section, with Clear Plexiglas printing and Opal Plexiglas printing. Other materials to print on are Sandwich panel printing and Corrugated plastic printing. If instead of backlit panels you need cut-out letters without printing, see the Plexiglas lettering. All printed rigid supports are collected in Panel printing, advertising signs.
Dall’idea al file pronto per la stampa
Con il servizio di progettazione grafica puoi creare una nuova composizione, vettorializzare un logo o adattare immagini e impaginazione al prodotto scelto. Condividi materiali e indicazioni in chat e rivedi le anteprime prima della preparazione dei file finali.
Scopri il servizio di progettazione grafica
Il servizio grafico è incluso nel prezzo di stampa?
La progettazione grafica è un servizio a pagamento, acquistabile separatamente. Il controllo del file di stampa rimane compreso nel prezzo del prodotto; per creare o modificare la grafica puoi acquistare il servizio dedicato.
Total: 49,96 € (VAT included)